 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| PI5C6800C 10-Bit Bus Switch with Precharged Outputs Features * Near-Zero propagation delay * 5 switch connection between two ports * Ultra low quiescent power (0.2A typical) * Ideally suited for Notebook Applications * A port is hot swapable * Packaging (Pb-free & Green available): - 24-pin 150-mil wide QSOP (Q) - 24-pin 173-mil wide TSSOP (L) Description Pericom's Semiconductor's The PI5C6800C is a 10-bit bus switch with low On-State resistance. The bus switch creates no additional propagation delay. The switch is turned on by a single enable (ON) input. When ON is LOW, the switch is on and port A is connnected to port B. When ON is HIGH, the switch between port A and port B is open and the B port is precharged to BIASV through the equivalent of a 10k-ohm resistor. Block Diagram 13 Pin Configuration ON A1 A2 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 VCC B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 BIASV A1 23 B1 A3 A4 A5 A6 A10 14 B10 A7 A8 A9 A10 ON GND Truth Table(1) Function Connect Precharge ON L H B1 - B10 A1 - A10 BIASV Note: 1. H = High Voltage Level, L = Low Voltage Level 07-0073 1 PS8351F 03/23/07 PI5C6800C 10-Bit Bus Switch with Precharged Outputs Absolute Maximum Ratings Over Free-Air Temperature Range(1) (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature....................................... -65C to +150C Supply Voltage Range .......................................... -0.5V to +7V DC Input Voltage(2) .............................................. -0.5V to +7V Input Clamp Current, IIK (V1<0) ....................................-50mA DC Output Current ..........................................................120mA Power Dissipation(3) ...........................................................0.5W Notes: 1. Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 3. The maximum package power dissipation is calculated using a junction temperatue of 150C and a board trace length of 750 mils. Recommended Operating Conditions Parameters VCC BIASV VIH VIL TA Description Supply Voltage Supply Voltage High-level input voltage Low-level input voltage Operating free-air voltage -40 Min. 2.3 1.3 2 0.8 85 C Typ. 5.5 VCC V Units Electrical Characteristics (Over Recommended Operating Free-air Temperature Range) Parameters VIK II IO ICC ICC (2) Test Condidtion VCC = 4.5V, II = -18mA VCC = 5.5V, VI = 5.5V or GND VCC = 4.5V, BIASV = 2.4V, VO = 0 VCC = 5.5V, IO = 0, VI = VCC or GND VCC = 3.6V, One input at 2.7V Other at VCC or GND VI = 3V or 0 VO = 3V or 0, Switch Off VCC = 4V VI = 2.4V, II = 15mA VI = 0V, II = 64mA VCC = 4.5V VI = 0V, II = 30mA VI = 2.4V, II = 15mA Min. Typ.(3) Max. -1.8 5 Units V A mA A mA pF -0.20 100 2.5 3.5 4.5 9 5.5 5 9 28 8 8 16 CIN COFF RON(1) Notes: 1. Measured by the voltage drop between the A and B terminals at the indicated current through the switch. On-State resistance is determined by the lower of the voltages of the two (A or B) terminals. 2. This is the increase in supply current for control input. 3. All typical values are at VCC = 3.3V, TA = 25C. 07-0073 2 PS8351F 03/23/07 PI5C6800C 10-Bit Bus Switch with Precharged Outputs Switching Characteristics (Over Recommended Operating Free-air Temperature Range, CL = 50pF) Parameter tPD(1) tPZH tPZL tPHZ tPLZ BIASV = GND BIASV = 3V BIAS = GND BIAS = 3V Test Conditions From (Input) A or B ON ON To (Input) B or A A or B A or B 3.1 3.6 2.7 3 VCC = 5V 0.5V Min. Max. 0.25 5 5 5 5 VCC = 4V Min. Max. 0.25 6 6 5.5 5.5 ns Units Notes: 1. This parameter is warranted but not production tested. The propagation delay is based on the RC time constant of the typical On-State resistance of the switch and a load capacitance of 50pF, when driven by an ideal voltage source (zero output impedance). Parameter Measurements 7V S1 From Output Under Test CL = 50pF (See note 1) Open GND Test tPD tPLZ/tPZL tPHZ/tPZH S1 Open 7V Open LOAD CIRCUIT Output Control (Low Level Enabling) Output Waveform 1 S1 at 6V (see Note 2) Output Waveform 2 S1 at Open (see Note 2) 1.5V tPZL 1.5V VOL +0.3V tPZH 1.5V tPHZ tPLZ 1.5V 3V 0V 3.5V VOL VOH VOH -0.3V 0V 3V Input tPLH 1.5V 1.5V 1.5V 0V tPHL VOH Output 1.5V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES Notes: 1. CL includes probe and jig capacitance. 2. Waveform 1 is for an output with internal conditions such that the output is LOW except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is HIGH except when disabled by the output control. * All input pulses are supplied by generators having the following characteristics: PRR < 10MHz, Zo = 50, tr 2.5ns, tf 2.5ns. * The outputs are measured one at a time with one transition per measurement. * tPLZ and tPHZ are the same as tdis. * tPZL and tPZH are the same as ten. * tPLH and tPHL are the same as tpd. 07-0073 3 PS8351F 03/23/07 PI5C6800C 10-Bit Bus Switch with Precharged Outputs Applications Information Logic Inputs The logic control inputs can be driven up to +5.5V regardless of the supply voltage. For example, given a +5.0V supply, the control input(s) may be driven low to 0V and high to 5.5V. Driving the control input(s) Rail-to-Rail(R) minimizes power consumption. Power-Supply Sequencing Proper power-supply sequencing is recommended for all CMOS devices. Always apply VCC before applying VBIAS and signals to the input/output or control pins. Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd. Packaging Mechanical: 24-pin TSSOP (L) 24 .169 .177 4.3 4.5 .0075 .0098 0.19 0.25 1 .303 .311 7.7 7.9 .047 Max 1.20 0.45 0.75 .252 BSC 6.4 SEATING PLANE .018 .030 .0255 BSC 0.65 .007 .012 0.19 0.30 .002 0.05 .006 0.15 07-0073 4 PS8351F 03/23/07 PI5C6800C 10-Bit Bus Switch with Precharged Outputs Packaging Mechanical: 24-pin QSOP (Q) 24 .008 0.20 MIN. .008 .013 0.20 0.33 Guage Plane .150 .157 3.81 3.99 .010 0.254 1 .337 .344 8.56 8.74 Detail A .016 .035 0.41 0.89 .041 1.04 REF 0-6 .033 0.84 .053 .069 1.35 1.75 .015 x 45 0.38 Detail A .007 .010 SEATING PLANE .004 0.101 .010 0.254 .016 .050 0.406 1.27 .228 .244 5.79 6.20 0.178 0.254 .025 typical 0.635 .008 0.203 .012 0.305 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS Ordering Information Ordering Code PI5C6800CL PI5C6800CLE PI5C6800CQ PI5C6800CQE Package Code L L Q Q Package Description 24-Pin 173-mil TSSOP Pb-free & Green, 24-Pin 173-mil TSSOP 24-Pin 150-mil QSOP Pb-free & Green, 24-Pin 150-mil QSOP Notes: * Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ * E = Pb-free & Green * Adding an X suffix = Tape/Reel Pericom Semiconductor Corporation * 1-800-435-2336 * www.pericom.com 07-0073 5 PS8351F 03/23/07 |
Price & Availability of PI5C6800C
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |